Sprinkler Head & Nozzle Repair in Brownsville, TX
Sprinkler heads take more abuse than any other part of the system. Mowers clip them, cars roll over them and grass grows over them. We replace broken heads, clear clogged nozzles and adjust the spray so water lands on the lawn and beds, not your driveway or the side of the house.
Signs you need head or nozzle repair
- A head is snapped off, cracked or gushing water
- Spray hits the driveway, sidewalk, fence or house wall
- A head is tilted, sunk below the grass or stuck in the up position
- Dry brown arcs appear between heads that should overlap
- A nozzle sputters, mists or throws an uneven pattern
- A rotor head stopped turning and waters only one spot
What we do
Head repair sounds simple, but a good fix also checks the coverage around it. Here is what we do.
- 1
Look
We run the zone and watch every head in it, not just the one that is obviously broken.
- 2
Diagnose
We check for clogged nozzles and filter screens, mismatched nozzles in the same zone, heads set at the wrong height and spray blocked by plants.
- 3
Explain the price
You get a clear price for the heads and nozzles that need work before we replace anything.
- 4
Repair and test
We install the right head for the spot, set the arc and distance, raise or level heads as needed and run the zone again to check coverage.
Overspray is more than a wet driveway
Water that lands on concrete runs straight into the street. It does nothing for the lawn and it is exactly the kind of waste drought rules target. A small nozzle change or a quarter turn on an adjustment screw often fixes it.
Mixed nozzles are another common problem. When one head in a zone puts out much more water than its neighbors, part of the lawn gets soaked while another part goes thirsty. Matching the nozzles evens it out.
Spray hitting a stucco or painted wall day after day can stain it and keep the base damp. If a bed runs along the house, we may suggest converting that strip to drip so the water goes to the roots instead.
Heads also wear out from the inside. The wiper seal that keeps water from leaking around the pop-up stem hardens with sun and heat, and the spring that pulls the stem down can weaken. When that happens, the head leaks at the base or stays up after the cycle, where a mower can catch it.
We carry common spray heads, rotors and nozzles on the truck, so most head repairs are finished on the first visit.
If a head keeps getting broken in the same place, such as along a driveway edge or a path the kids use, we can move it back a few inches or swap it for a sturdier model so it stops happening.
Quick checks before you call
- Run each zone for a minute and walk it. Look for heads that do not pop up, spray sideways or leave a puddle at their base.
- Pull grass away from any head that seems buried and see whether it clears the turf once it rises.
- Mark broken heads with a flag or a stick so they are easy to find when we arrive.
Head problems we see in Brownsville yards
St. Augustine grass grows fast in the Valley's heat and long season. Its runners creep over heads and block the spray, and edging around them becomes a regular chore. Raising a head to the right height or switching to a taller pop-up often solves it for good.
Some properties near resacas or on irrigation district water run non-potable water through their sprinklers. Silt and organic material in that water clog nozzles and filter screens much faster than city water does. If that sounds like your system, we clean the screens, check the nozzles and talk with you about a filter that fits.
Request your free estimate
Tell us what your system is doing. We will call you back to talk it through and set up a time to look.
Sprinkler Head & Nozzle Repair: common questions
Can you just replace the one broken head?
Yes. If the rest of the zone is working, we replace the head and match its nozzle to its neighbors so coverage stays even.
Why does my sprinkler spray the street?
Usually the arc or distance setting has shifted, the wrong nozzle was installed or the head was knocked out of line. We adjust or replace it so the spray stays on the grass.
What is a rotor, and how is it different from a spray head?
A spray head throws a fixed fan of water over a short distance. A rotor turns slowly and throws a stream much farther, which suits larger lawn areas. The two should not be mixed in the same zone because they apply water at very different rates.
Why do my nozzles keep clogging?
Dirt gets in after a line repair, or the system runs on resaca or other untreated water that carries silt. Cleaning the filter screens and flushing the lines helps, and a filter may be worth adding.
Do you fix sprinkler heads that are buried in the grass?
Yes. We dig them out, raise them to the right height on a new riser or replace them with a taller head, and clear the grass around them.
Related services
Leak & Broken Pipe Repair
Soggy spots, bubbling soil and a climbing water bill usually point to a cracked line or a worn valve. We find it and fix it.
Learn more →Drip Irrigation Repair & Installation
Drip lines water beds, palms and shrubs at the roots with very little waste. We repair drip zones and convert spray beds.
Learn more →Sprinkler Tune-Ups
A seasonal checkup catches small problems early and resets the timer, so you get a greener lawn with less water.
Learn more →